Adapters

A0030 Fill Adapter

Click here to view this product in our catalog

The Emco Wheaton A0030 Adapter is designed for use with conventional dual point fill systems. Features recessed threads for easy installation and positive seating on riser pipes. Use with the A0097 Fill Cap. Notched variants are for use with the A0032-001 Adapter Clamp and comply with EPA 40 CFR Part 63 requirements.

Material
Body: Aluminum or Brass
Gasket: Buna-N

A0030-124S Fill Swivel Adapter

View Catalog Page

View Product Cutsheet

The Emco Wheaton A0030-124S Swivel Fill Adapter typically installs on the tank fill riser. The top of the adapter rotates 360 degrees while the base is stationary, preventing accidental
loosening from the riser during fuel deliveries. The A0030-124S is field serviceable using the kits below. Use with the A0097 Fill Cap. Use the Emco Wheaton A0081-001 Adapter
Wrench for installation and removal.

Material
Body: Brass or Stainless Steel
O-rings: Viton®
Gasket: Buna-N
Viton® is a registered trademark of
DuPont Dow Elastomers.

 

A0030 Tank Probe Adapter

Click here to view this product in our catalog

The Emco Wheaton A0030-014F Tank Probe Adapter is designed for use with the Franklin Fueling INCON Tank Probe.  Includes the aluminum body, aluminum support washer and two rubber gaskets.  INCON support plate not included.

 

 

A0089, A0096 Coaxial Fill Adapters

Click here to view this product in our catalog

Emco Wheaton Coaxial Vapor Recovery Adapters are designed for standard coaxial fill systems and coaxial systems with self-sealing vapor lines. Features recessed threads for easy installation and positive seating on riser pipes. Use with the A0097 Fill Cap. Use Emco Wheaton A0081 Adapter Wrench for installation.

The A0089 and A0096 are notched for use with the A0032-001 Adapter Clamp to comply with EPA 40 CFR Part 63 requirements.

Material
Body: Aluminum

A0032 Adapter Clamp

Click here to view this product in our catalog

The Emco Wheaton A0032-001 Adapter Clamp installs on the riser pipe or pipe nipple. The A0032 is used with the following non-swivel adapters: A0089, A0096, A0030-024A, A0030-024BA and A0076-005. The tabs are aligned with the notches on the adapter, and the three set screws are tightened to prevent the adapter from loosening in use, in compliance with EPA 40 CFR Part 63 requirements.

Material
Body: Aluminum

 

A0033 Debris Collector

Click here to view this product in our catalog

The Emco Wheaton A0033-004 Debris Collector attaches to the bottom of any fill adapter to prevent large debris from entering the underground storage tank. There are no restrictions during a fuel drop, and the center hole allows for fuel sampling.

Material
Rag Stopper: Stainless Steel
Gasket: Nitrile

 

A0076 Vapor Adapter

Click here to view this product in our catalog

The Emco Wheaton A0076 Vapor Adapter is used in dual point fill systems on the vapor return line. It features a poppet design which seals off the vapor path and external lugs on the adapter
body for easy installation. Use with the A0099-002 Vapor Cap.

Material
Body: Aluminum
Gasket: Buna-N

 

 

 

  • CARB E.O. G-70-97-A
    ULC Listed MH27242

A0076-124S Vapor Swivel Adapter

View Catalog Page

View Product Cutsheet

The Emco Wheaton A0076-124S Vapor Swivel Adapter typically installs on the tank vapor riser. The top of the adapter rotates 360 degrees while the base is stationary, preventing accidental
loosening from the riser during fuel deliveries. A normally closed poppet valve opens to recover the vapor. The A0076-124S is field serviceable using the kits below. Use with the A0099-002
Vapor Cap. Use the Emco Wheaton A0081-001 Adapter Wrench for installation and removal.

Material
Body: Brass or Stainless Steel
O-rings: Viton®
Gasket: Buna-N
Viton® is a registered trademark of
DuPont Dow Elastomers.

 

  • Complies with EPA 40 CFR Part 63